Maxus MXN10300 User Manual download pdf (Page 2)

MXN10300

Operating Instructions

Air leaking at trigger valve

area.

Air leaking between hous-

ing and nose.

Air leaking between hous-

ing and cap.

Stapler skips driving staple.

Stapler runs slow or has

loss of power.

Staples are jammed in sta-

pler.

Air leaking at trigger valve

stem.

O-Rings in trigger valve housing are

damaged

Loose screws in housing

Damaged O-Rings

Damage to bumper

Loose screws

Damaged gasket

Worn bumper

Dirt in nose piece

Dirt or damage prevent staples or

pusher from moving freely in maga-

zine

Damaged pusher spring

Inadequate air flow to stapler

Worn O-Ring on piston or lack of lubri-

cation

Damaged O-Ring on trigger valve

Air leaks

Cap gasket leaking

Stapler not lubricated sufficiently

Broken spring in cylinder cap

Exhaust port in cap is blocked

Guide on driver is worn

Staples are not correct size

Staples are bent

Magazine or nose screws are loose

Driver is damaged

Staples loaded incorrectly

O-Rings or seals are damaged

Replace o-rings and check operation of Work Contact

Element (WCE)

Tighten screws

Replace o-rings

Replace bumper

Tighten screws

Replace gasket

Replace bumper

Clean drive channel

Clean magazine

Replace spring

Check fitting, hose, or compressor

Replace and lubricate o-rings

Replace o-rings

Tighten screws and fittings

Replace gasket

Lubricate stapler

Replace spring

Replace damaged internal parts

Replace guide

Use only recommended staples

Replace with undamaged staples

Tighten screws

Replace driver

Review Loading/Unloading section in this manual

Replace o-rings or seals

Troubleshooting Guide

Stop using stapler immediately if any of the following problems occur. Serious personal injury

could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized

Service Center.

WARNING

Problem Cause Solution

General Safety

Information (Continued)

Danger indicates

an imminently haz-

ardous situation which, if not avoided,

WILL result in death or serious injury.

 Read and understand

tool labels and manual.

Failure to follow warn-

ings, dangers, and cau-

tions could result in

DEATH or SERIOUS INJURY.

 Do not use any type

of reactive gases,

including, but not lim-

ited to, oxygen and

combustible gases, as

a power source. Use

filtered, lubricated, regulated com-

pressed air only. Use of a reactive

gas instead of compressed air may

cause the tool to explode which will

cause death or serious personal

injury.

 Use only a pressure-

regulated compressed

air source to limit the

air pressure supplied

to the tool. The regu-

lated pressure must

not exceed 100 psi. If the regulator

fails, the pressure delivered to the

tool must not exceed 200 psi. The

tool could explode which will cause

death or serious personal injury.

 Never use gasoline

or other flammable

liquids to clean the

tool. Never use the

tool in the presence

of flammable liquids or gases.

DANGER

Vapors could ignite by a spark and

cause an explosion which will result

in death or serious personal injury.

 Always remain in a

firmly balanced

position when

using or handling

the tool.

 Do not remove, tam-

per with, or other-

wise cause the Work

Contact Element

(WCE) or trigger to

become inoperable.

Do not operate any

tool which has been modified in a

like fashion. Death or serious per-

sonal injury could result.

 Do not touch

the trigger

unless driving

fasteners.

Never attach

air line to tool

or carry tool

while touching the trigger. The tool

could eject a fastener which will

result in death or serious personal

injury.

Warning indicates

a potentially

hazardous situation which, if not avoid-

ed, COULD result in death or

serious injury.

 Always discon-

nect the tool

from the power

source when

unattended,

performing any

maintenance or

WARNING

repair, clearing a jam, or moving the

tool to a new location. Always

reconnect the air line BEFORE load-

ing any fasteners. Do not load the

tool with fasteners when either the

trigger is depressed or the Work

Contact Element (WCE) is engaged.

The tool could eject a fastener caus-

ing death or serious personal injury.

 Always fit tool

with a fitting or

hose coupling

on or near the

tool in such a

manner that all

compressed air in the tool is dis-

charged at the time the fitting or

hose coupling is disconnected. Do

not use a check valve or any other fit-

ting which allows air to remain in the

tool. Death or serious personal injury

could occur.

 Never place hands or

any other body parts in

the fastener discharge

area of the tool. The

tool might eject a fas-

tener and could result

in death or serious personal injury.

 Never carry the

tool by the air

hose or pull the

hose to move the

tool or a compres-

sor. Keep hoses

away from heat,

oil and sharp edges. Replace any

hose that is damaged, weak or

worn. Personal injury or tool dam-

age could occur.

MXN10300

Operating Instructions

100

psi

Latch

Magazine

Work contact

element (WCE)

Fastener discharge area

Trigger

Fastener loading area

Cap exhaust

Tool Components and Specifications

• REQUIRES: 0.8 SCFM with 10

fasteners per minute @ 90 PSI

• AIR INLET: 1/4” NPT

• STAPLE SIZE RANGE: 3/8” to 1-1/4”

• MAGAZINE CAPACITY:

100 Staples per load, 18 gauge

• WEIGHT: 2 lb., 15 oz.

• LENGTH: 10-1/2”

• HEIGHT: 9-1/2”

• MAXIMUM PRESSURE: 100 PSI

• PRESSURE RANGE: 60 – 100 PSI

Nozzle shield

Quick clear nose

Adjustable depth control

(not visible)

1 2 3 4

Comments to this Manuals

No comments

Maxus MXN10300 User Manual Page 2

Comments to this Manuals

Related products and manuals for Power tools Maxus MXN10300